Besoin d'aide pour décripter message erreur

Bonjour,

Les problèmes sont signalés par le mot clé SEVERE, les WARNINGS sont des alertes non bloquantes parfois justifiées parfois non.

Dans votre cas, E+ a un problème de calcul de la distribution solaire dans vos locaux. Ceci est du à l'option Intérieur et Extérieur Complet de la boite de lancement des simulations.
Cette option est contraignante car les locaux doivent être bien convexe (chaque paroi doit voir les autres en direct), de forme peu compliquée. Dans votre cas, la zone 29146 (voir le fichier idf pour trouver le nom correspondant) a un problème avec la paroi W_29146_4_0_0.

Soit votre géométrie peut être simplifiée, soit vous devez utilisez l'option Extérieur Complet de la distribution solaire.

Cordialement,

Bonjour,

Je débute avec DB, je suis pour le moment avec la version d'essai (licence en commande cette semaine...)

Mon problème: après l'ajout d'une isolation à mes murs, la simulation se bloque avec le message d'erreur suivant: (désolé pour la longueur, je ne sais pas ce qui est important à lire ou pas et je ne suis pas parvenu à joindre mon fichier .txt sur le forum...)

Quel est le problème ?? (ou les problèmes) Merci d'avance.

Program Version,EnergyPlusDLL 3.0.0.028, 08/04/2009 16:01,IDD_Version 3.0.0.028
************* Beginning Zone Sizing Calculations
** Warning ** Site:GroundTemperature:BuildingSurface: Some values fall outside the range of 15-25C.
** ~~~ ** These values may be inappropriate. Please consult the Input Output Reference for more details.
** Warning ** GetWindowBlind: Slat Width [7.00E-003] is less than Slat Separation [1.90E-002].
** ~~~ ** This will allow direct beam to be transmitted when Slat angle = 0. For material=20001
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=29146
** ~~~ ** because vertex 1 of back surface=W_29146_4_0_0 is in front of receiving surface=W_29146_3_1_0
** ~~~ ** (Dot Product indicator=0.9163)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=29146
** ~~~ ** because vertex 2 of back surface=W_29146_4_0_0 is in front of receiving surface=W_29146_3_1_0
** ~~~ ** (Dot Product indicator=0.9163)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=29146
** ~~~ ** because vertex 3 of back surface=W_29146_4_0_0 is in front of receiving surface=W_29146_3_1_0
** ~~~ ** (Dot Product indicator=2.7030)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=29146
** ~~~ ** because vertex 4 of back surface=W_29146_4_0_0 is in front of receiving surface=W_29146_3_1_0
** ~~~ ** (Dot Product indicator=2.7030)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.

...
** Warning ** DeterminePolygonOverlap: Too many figures [>15000] detected in an overlap calculation. Use Output:Diagnostics,DisplayExtraWarnings; for more details.
** Warning ** DeterminePolygonOverlap: Too many vertices [>12] detected in an overlap calculation. Use Output:Diagnostics,DisplayExtraWarnings; for more details.
** Severe ** Temperature out of bounds (-151.43) for surface=W_28832_2_0_0
** ~~~ ** in Zone=28832
** ~~~ ** During Warmup & Sizing, Occurrence info=SUMMER DESIGN DAY IN HABITAT GROUPÉ - PALAISEAU, 07/15 11:00 - 11:04
** ~~~ ** A temperature out of bounds problem can be caused by several things. The user
** ~~~ ** should check the weather environment, the level of internal gains with respect
** ~~~ ** to the zone, and the thermal properties of their materials among other things.
** ~~~ ** A common cause is a building with no thermal mass -- all materials with
** ~~~ ** Regular-R definitions.
** Fatal ** EnergyPlus has exited due to the reason stated above
...Summary of Errors that led to program termination:
..... Reference severe error count=133
..... Last severe error=Temperature out of bounds (-151.43) for surface=W_28832_2_0_0
************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
** Warning ** DXFOut: Could not triangulate surface="W_29146_9_0_1", type="Wall", check surface vertex order(entry)
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
** Warning ** DXFOut: Could not triangulate surface="W_29173_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29173_5_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28490_5_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28600_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28632_5_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28748_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28748_7_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28764_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28832_2_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_28903_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29199_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29199_5_1_0", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29199_8_1_0", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29059_3_0_1", type="Wall", check surface vertex order(entry)
** Warning ** DXFOut: Could not triangulate surface="W_29083_4_0_1", type="Wall", check surface vertex order(entry)
************* EnergyPlus Terminated--Fatal Error Detected. 20 Warning; 133 Severe Errors; Elapsed Time=00hr 07min 47.47sec